
Add to Cart
Pure Copper Transformer Pure Sine Wave Power Inverter LED / LCD Display
Feature:
On inverter:
• High overload ability
• Low battery voltage trip selectable, extracting max power from various batteries with different protections.
• Low quiescent current, selectable sensing cycle to reduce power consumption.
On battery charger
• 3-step intelligent battery charging.
• 8 preset battery type selector plus de-sulphation for totallly flat batteries.
• Powerful charge rate up to 70Amp, selectable charging current.
• PFC(Power Factor Correction) for charger, less power consumption than conventional units.
On Transfer
• Delay before transfer, extra protections for loads under generator mode.
• Input AC voltage range selectable, for different kinds of loads.
• 8 ms typical transfer time, guarantees power continuity.
• 30A/40A through current ablility.
• Output voltage regulation optional.
On remote control & other featuers
• Ability to switch the unit on/off.
• Ability to select/deselect power saver mode.
• 17 alarms/warnings, informative for easier operation and trouble-shooting.
• LCD status display available.
• RS232 communication port optional.
Specification:
Model NO. | 8048E/8096E | 10048E/10096E | 12048E/12096E | |
Norminal Power | 8000W | 10000W | 12000W | |
AC Input | Phase & waveform | single phase & sinewave | ||
voltage | 220Vac/230Vac/240Vac | |||
Acceptable Voltage | 154-273Vac | |||
Line Low Transfer | 154V | |||
Line Low Return | 164V | |||
Line High Transfer | 273V | |||
Line High Return | 263V | |||
Frequency | 50Hz or 60Hz(Auto Sensing) | |||
Line Low Transfer | 40Hz | |||
Line High Transfer | 80Hz | |||
Output | Phase & waveform | Single phase & sinewave(bypass mode sync to input) | ||
voltage | 220Vac/230Vac/240Vac(same as input on bypass mode) | |||
Voltage Regulation | ±10%rms(bypass mode sync to input) | |||
Frequency | 50Hz or 60Hz(Auto Sensing) | |||
Crest Power | 3 times of ratings | |||
Short Circuit Protection | Yes, shutdown | |||
Power Factor | 0.9~1.0 | |||
DC Input | Battery Voltage | 48V | ||
Minimum Start Voltage | 40V | |||
Low Battery Alarm | 44V | |||
Low Battery Transfer | 40V | |||
High Voltage Alarm | 64V | |||
Max Charging Current | 75A | 85A | 100A | |
Over Charge Voltage | 62.8V | |||
Transfer | Line Mode | >95% | ||
Efficiency | Battery Mode | >85% | ||
Power Saver | Available when the load is less than 75 Watts | |||
Indicators | LCD Display | Input Voltage,Output Voltage,Frequency,battery Voltage,Load, | ||
Temperature,Charge Current,Fault | ||||
4-LED Display | Charge,Line,Inverter,Fault | |||
LCD Display | Input Voltage,Output Voltage,Frequency,Battery Voltage,Load | |||
Switch selector | Saving Mode is on/off when push the switch forwards/backwards, | |||
keeping it horisontal is turning the inverter off | ||||
Audible Alarm | Sounding when the heatsink's tem is over 105ºC and shutdown | |||
after 30 seconds | ||||
Protections | low battery,over charging,over temp,over load | |||
Communications | RJ11/RS232(Optional) | |||
Enviro-mental | Operating Environment | 0-40ºC,0-95%RH(non-condensing) | ||
Audible Noise | <60dB | |||
Net Weight(KG) | 56 | 64 | 68 | |
Dimension (mm) | 549*450*201.2 | 584*450*201.2 |